Breaking News
Free Time

Wastin’ Time: Making every second count when carving a clock face

By Jess Mancini 5 min read

If you haven't already done so, you should try to see a show sponsored by the Gepetto Woodcarvers. These guys are master craftsmen and artisans of the highest order.

I don't carve. I try to carve, but I don't carve. Does that make sense? What I'm saying is the scratchings I make on a piece of wood is not an example of carving. It is an example of someone who has no idea of what to do.

I should take a class to at least learn the rudiments.

Like I've said several times, not knowing how to do something hasn't stopped me before. I do have my limits. I wouldn't try to fly an airplane.

But carving a caricature of the sun isn't the limit and is the basis for this theme on how to make something in your shop.

I wanted to carve the face of the sun on a wooden disk for a kitchen clock for my wife. I've spent hours watching YouTube videos and reading everything I could on the internet about carving a sun face. I found several renderings by artists and came up with an idea of what the face should look like. I drew several examples and finally chose a face I thought I could have at least half a chance of carving.

Boy was I wrong.

The face was going to be about 8 inches in diameter and surrounded by 12 sunbeams, one beam for each number on the dial. I glued two 15 inch 1-by-8 pieces edge-to-edge and scribed a circle of about 15 inches, whatever the dimensions of the glued boards would allow.

I used a router with a quarter inch dado bit to cut a circle of 9 inches within the first circle. This would create the raised face of the clock and be the divider from the rays to the face.

Cutting the sunbeams was easy. I divided the circle into 12 segments and, with the lines as points of intersection, I used a lid of about 7 inches in diameter to draw the curves of the tips of the rays. One side was concave and the other was convex. I used a scroll saw and took care to cut the rays in two passes, one for each side of the ray, so I can use the scrap in case they are needed for another clock project.

From the beginning, I didn't want the clock to look like it was made on an assembly line where each cut would be as exact as exact could be. I wanted it to look like it was made by hand.

I rasped the sunbeams into a shape I thought was pleasing, then sanded them by hand and with a sander. They turned out pretty good with enough variations to look like a flame coming from a candle.

Then came the hard part for me. I found artists' renditions of the face of the sun and created a composite of what I thought I could carve. I bought inexpensive carving tools. I wasn't going to spend hundreds of dollars on something I was going to use once in a while. The chisels were OK after they were sharpened and honed, but when I say they were OK, that's from the perspective of someone who didn't know what he was doing. Someone with more experience and ability may not have had any trouble.

I don't blame the tools and to make a long story short, the carving was so bad I stopped. My philosophy is when you're trying to get out of a hole, quit digging, so I planed the face of the clock. I abandoned the idea of carving the face of the sun for this project. I haven't given up hope that some day I will be able to carve a face.

I forgot to mark the center of the clock, so after I again found the center and scribed 12 lines, I used walnut plugs to mark the numbers on the dial. I purchased a clock mechanism with 4 inch hands, but I had to order a second hand.

I made an area in the rear of the clock using half-by-three quarter inch wood slats for the mechanism. I made a hanging hook from scrap sheet metal.

I finished the clock with a gel stain from Minwax, old oak or something, which I don't believe tinted the pine very much. I then sprayed it with three coats of gloss lacquer, lightly sanding between coats.

I have to say the clock turned out fine. I gave it to my granddaughter for her daughter's bedroom.

I'll make another one for my wife after I learn a little bit about carving.

***

Unless you think this column wasn't enough of a waste of time, send ideas for "Wastin' Time with Jess Mancini" to Jess Mancini at jmancini@newsandsentinel.com.

Starting at /week.